Suzican list

[Evolvocane]

Man. I did this last year with the X-90. You alwayz think you got time. Stuff keeps coming up. The shop is packed and after working on other peoples rides all bloody day I have next to no energy for my own. Heres my list that I started this weekend.

1. Front third member -DONE
2. Fab new front third mount -DONE
3. re + re new rear axle bearings and seals - DONE
4. re+ re new rear wheel cyl. shoes and spring kit -DONE
5. Unlock rear diff - DONE
6. Install new t-case
7. patch rear floor
8. install duster, windjammer and bikini top
9. inspect and replace EZ clutch
10. starter
11. front pads and rotors - DONE
12. Fab new rear spring pockets - DONE
13. oil change - DONE
14. fab new rear third link
15. winch plate
16. Install winch

I think its gonna be down to the wire. I have school, work and family shit on top of that.

[whateverworks]

Things to do:
Some trimming to rear wheel wells...
Install Lock Right locker...
Passenger CV shaft...
Install diff drop brackets...
Change all fluids...
Lube hubs n wheel bearings...
Lets Rock :)
Kelly

[longy442]

I think I'm pretty much done on the zook, as done as I'm gonna be for this year anyway. I just completed a full rear roll cage, a hoop to match the main hoop and installed two rear seats and belts. Look pretty good. won't get picks, see you at suzican.

I only have two days off work before leaving, still have to pack the RV full of tools and food and beer. hope she flat tows for 8 hours ok.

Good luck to all at getting everything done

[TheSarg]

Install upgraded motor
install upgraded tranny
install axles
lift it
do some sort of custom cage
new brake/fuel lines
make it run good
install seats


hahahaahahahaha

[SamiFlyer]

My list is still way too long! :roll:

Just pulled the engine apart to see why it was leaking oil everywhere.
The valve cover gasket was shot so no big deal but the sludge inside the top-end was just unimaginable! Also the two screws that hold the rocker shaft on #3 were loose inside. One of them got munched and won't thread back in! Cam lobe for #4 took a shit-kicking. The bottom end was leaking too so I pulled the timing cover off and it was just full of oil. The timing belt looks new but it's oil-soaked so I can't trust it. The timing cover has been worn through not only by the crank pulley but also the water pump pulley. The oil pump had been put in with what appears to be an incomplete used gasket and RTV but it didn't hold up and that's why there was spooge all over the place. I'm going to have to drop the pan and get new gaskets and I was expecting that but the cam did it for me. I've got no choice to pull the engine from the 93 parts truck and toss it in my 4dr. I'll rebuild this engine later.

[Grumpy]

For those of you crying you got stuff to do to one truck....suck it up buttercups......I got two to get ready.......
Mine - Swap in new zuk leaf packs in front
Build ramps to load into back of dump truck, (see thread under "Coming out of hibernation....Finally)

Hers - Front brakes
Clean and repack front knuckles
New shoes, turn drum for E-brake, and adjust
Weld front supports and main hoop to frame for cage
Install new cap and rotor
Install spacer on front D-shaft
Drain and refill F+R diffs
Padding on cage (she already at Spring Fever hit her head three times)
Fab spare tire and High Lift mount
Mount spare on rim
Re-weld front lower shock mount
Change clutch???

Oh yeah, and I'm down to basically one whole day to do everything...I do my best work under pressure...hehehehehehe...see ya there!!

[Mud Lite]

Hmmmmmmmmmmmmmmm, where have I heard that line before?????????

Lets see , my list: put on trailer, fill gas tank! She's still all good after Moab:thefinger

I could write a book on what I have to do to HER JP plus I have the ongoing Flattie Project.

[vanbdan]

Well ,

1.Buy zook
2.Drive zook
3.hope Zook needs nothing.
4.see ya there.

[Canadian_zuk]

mmmm, stupid list

remove fenders and put something else there - Done
install bright lights - done
install less bright lights - done
rebuild t-case - done
remove over flexy boomerang shackles and make new H-shackles - done
simplify wiring (toggles) - done
new spring eye bushings front - done
snorkle - done
fluids changed - done
relocate battery to cab - done

still to do:

back brakes
reverse light
repack bearings
change tires over to TSLs
anti wrap bar
fix wipers and install washer bottle/pump
paint? maybe.
gather spares and tools....

probably more I'm forgetting....

-CZ

[Gadzooks]

mmmm, stupid list

remove fenders and put something else there - Done
install bright lights - done
install less bright lights - done
rebuild t-case - done
remove over flexy boomerang shackles and make new H-shackles - done
simplify wiring (toggles) - done
new spring eye bushings front - done
snorkle - done
fluids changed - done
relocate battery to cab - done

still to do:

back brakes
reverse light
repack bearings
change tires over to TSLs
anti wrap bar
fix wipers and install washer bottle/pump
paint? maybe.
gather spares and tools....

probably more I'm forgetting....

-CZ

Why move the battery in?

[twistedzuki]

ha ha sharpen the mower...must do!!

[MuddMachine]

Install rear bumper w/pintle.
Buy tequila.

:D

[longy442]

ha ha sharpen the mower...must do!!


Dull the axe blade....just to make it more challenging.:brows:

[Fullload]

After Paragon last year, dropped it in garage.
before May 24 this year. fixed flat and charged battery. with the alternator.
After May 24 dropped in garage. Tires still holding air.


Load on trailer see ya there.

Zookvet and Depot need a little help but nothing major.

[Canadian_zuk]

Why move the battery in?

because, like a dumb ass, I forgot to make room for a battery under the hood when I redid the front clip.:rofl: Oh well, it's behind the glove box now.

[whateverworks]

Things to do:
Some trimming to rear wheel wells... FAWK IT
Install Lock Right locker.... DONE
Passenger CV shaft...
Install diff drop brackets... DONE
Change all fluids... DONE
Lube hubs n wheel bearings... DONE
Lets Rock :)
Kelly

[longy442]

I found a trailer I can borrow, (i was gonna flat tow) BUT last year i hammered in a 6" lift hitch with a sledge and it if in there solid. I got new rear leafs in the RV and now that hitch is too tall for the trailer, its great for tow bar. So I'm going to try and get that hitch out to put in a level one so I can use the borrowed trailer. I only have one day off before we leave so if it don't come out easy, I'll still be flat towing. Fawk it what ever gets us there.

[Depot]

hole in bogger sidewall... replaced tire with a spare - DONE
Fuel Cell Mounting tabs ripped cleaned off - Fulll's buddy is welding new ones on for me.. hopefully dun tomm
More padding for wife seat - maybe

D

[Evolvocane]

Most of my shit is done. Gonna make the steering shaft up tomorrow. After that. Load up and go!

[SamiFlyer]

Just got back from the shop. Fired up the motor finally. My ECM is blown so we needed to do some surgery on it. My mechanic is coming over tomorrow night to certify it. Still has no interior, mirrors, exhaust not finished, stereo not installed :D , no fluid in the t-case, bla bla bla. But I'll fawking be there!:rock:

[vanbdan]

Well ,

1.Buy zook
2.Drive zook
3.hope Zook needs nothing.
4.see ya there.

Well,time to edit this list...Couldn't get my shit together in time,so Gonna drive Stix's OTHER zook.At least I can have something to wheel this year.Thanks Stix.
See ya early Saturday morning.

[Evolvocane]

Just got back from the shop. Fired up the motor finally. My ECM is blown so we needed to do some surgery on it. My mechanic is coming over tomorrow night to certify it. Still has no interior, mirrors, exhaust not finished, stereo not installed :D , no fluid in the t-case, bla bla bla. But I'll fawking be there!:rock:


Nice man, have to drink some beers this weekend:)

[Zukinator]

Lets see..

replace all fluids - Done
Fix broken tranny mount - done
Rebuild starter - done
Install new from wheel bearings - ordered today..
clean mud from every orfis (sp?) of my truck - never ending
locate wiring short in lights - done
locate wiring short in wipers - seems ok now :) one less thing
Locate wiring short in truck/trailer for trailer brakes - hmm intermittent crap..
change time belt idler pully - done
breaks tires off bead clean shiat out and reseal.. - no time
fix leaky valve stem.. - no time
replace rear brake line - tomorrow


Will be there no matter :thefinger
Tim

[twistedzuki]

well I got all my intended chit done cept the e-locker....pooped the spiders for now..guess u will have to see when u get there!!:brows:

[SamiFlyer]

OK, She's certified.:D Going to go register it and plate it tomorrow. I started on the stereo (because a 5 hour trip to Calabogie without it is going to drive me nuts!) while Simon laid some fiberglass to smooth out the body lines.:brows:
We're painting it tomorrow night so it will just be a quickie.

I still have to throw some parts at it (cap, rotor, plugs and wires) and I have a leaking slip yoke. Not sure if I can get that seal tomorrow or Wednesday though.

I was shooting to leave by Thursday afternoon and stay at my bro-in-law's in Orleans. Might have to leave Friday morning now.

I took it for a small ride around the block and in the trails to flex it out (IFS with coil spacers flex???:rofl: ) and everything was ok but she wasn't shifting right. The vacuum modulator wasn't connected so I did that but haven't tested it yet. I also see a second connector on top of the t-case. Black two wire and it's not the 4x4 indicator light because it is plugged in and working. Anybody know what it could be? It could be coming off the tranny too (auto) but I haven't had a chance to really look.

[Depot]

maybe ur revers lites switch n ur tranny?

D

[Canadian_zuk]

or the torque converter lock up.

[SamiFlyer]

Thanks for the suggestions guys, I'll check those out tonight. :beer:

[Twinkie]

I was shooting to leave by Thursday afternoon and stay at my bro-in-law's in Orleans. Might have to leave Friday morning now.


Dude, "Hanmer" is Sudbury, right? You'll be coming down 17 right? You'll be driving right by us. Orleans is an hour and a half further then you need to go!

[SamiFlyer]

Dude, "Hanmer" is Sudbury, right? You'll be coming down 17 right? You'll be driving right by us. Orleans is an hour and a half further then you need to go!

Yeah my bro-in-law lives in Orleans. I know it's an hour and a half past but he has some stuff I need to get off of him. Friday will be an easy day if all I have to do is get up, buy groceries, ice and beer and then make it to Calabogie to set up camp.:D

[Twinkie]

Lots of guys come in from Orleans, maybe one of them would deliver for you, depending what it is. Hell, if he wants to deliver to central Ottawa I'll bring it for you.
Show up Thursday night and get a prime spot, by the sounds of it it may be slim pickings by Friday. LoL

[Loco]

I'll be back and forth to Orleans a couple of times this week before coming to Suzican. If what you need picking up is not too big I'd be more than happy to grab it for you.

[SamiFlyer]

Well we just primed the truck tonight and we'll be painting it tomorrow night. (Wednesday) I still have a whole bunch of parts to throw at it so we may be leaving Friday morning.:roll:

My bro-in-law is coming to meet me in Calabogie so he will be able to bring my stuff but thanks for the offers guys. :beer:

[Depot]

ok.. im almost ready.... fuel cell is in.. spare tire is fixed.. stereo components collected.....


lets hope it werks....

D

[kneedeep]

kick is the daily driver so nothin to fix If I can get a trailer lined up or mine fixed I may take the tour up this year won't know till fri. 2 days hmm!

[SamiFlyer]

Yup. Friday morning it is! :rant:

Sanded the primer, washed it down and painted it tonight. Early night to bed for me. :D
Long day tomorrow with all the stuff I still have to do.

[vanbdan]

Sounds like a great crowd,hope I can get a parking spot Saturday morning!

[frwinks]

ok.. im almost ready.... fuel cell is in.. spare tire is fixed.. stereo components collected.....


lets hope it werks....

D

all this shite better not blow my genny to holy fawk:thefinger

[SamiFlyer]

all this shite better not blow my genny to holy fawk:thefinger

You guys need a backup? 8hp 5000 watter with 115/230v output. I have a trailer so it's no big deal to bring it.

[Depot]

all this shite better not blow my genny to holy fawk:thefinger


Honestly.. I really dont know what were gonna use ur genny for.. couple lites in the tent and coffee maker is all I can think off....

All my stereo shit is car audio... 12 V only so the only way Im gonna blow ur genny is from the bass! :rofl: :rofl:

D

[Canadian_zuk]

Fawk. Well it's as done as it's gonna be. Didn't get a good portion of what needed to be done finished, but it's wheelable. Gotta packup and gather spares when I get home, we'll be leaving Friday morning EARLY. I hope to be in Calibogie before 10:00am, including a stop at the cottage for more shtuff. Can't fawking wait!!! See you there fawkers.:thefinger

-CZ


P.S. VAN, we'll save you a spot on the south side of the tracks.;)

[MuddMachine]

DONE! :thefinger

Late night, trucks done and so am I. Im off to work but the trucks ready with the towbar waiting. All I gotta do is grab some clothes when I get home and stop for ice and tequila :D

See you fawkers late tonight. ;)

[SamiFlyer]

Pulled an all-nighter! Got in at 8am. Just woke up from a nap. Gotta pack now! See you DSOBs tonight. :thefinger